Skip to page content


QSC RMX5050 POWER AMP - 2 X 1600W

Stock code: QSCRMX5050

Stock Availability

Auckland North Island South Island Warehouse

  • QSC


- The new flagship of the RMX line, the RMX 5050 provides extremely high power and represents tremendous value
- The RMX 5050 provides advanced thermal performance, delivering higher continuous power in 2-ohms stereo or 4-ohms bridged applications
- Dual mono, high current power supply for increased reliability and performance
- 3RU chassis only 16" deep
- Professional quality performance - incorporates road-proven QSC designs
- High-current toroidal transformers for greater two-ohm power and low noise
- Independent user-defeatable clip limiters reduce distortion
- Selectable low-frequency filters (30 Hz or 50 Hz) protect speakers and increase headroom
- Balanced 1/4" (6.3 mm) TRS, XLR, and barrier strip inputs for maximum flexibility
- Binding post and Neutrik Speakon outputs
- Front mounted gain controls for easy access
- Signal and Clip LED indicators to monitor performance
- 3-year warranty. An optional 3-year extended service contract is available. Ask your dealer for details.

RMX 5050 STEREO MODE, Both Channels Driven8 ohms 
  FTC 20 Hz - 20 kHz, 0.1% THD
  EIA 1 kHz, 0.1% THD
1050 W
1100 W4 ohms
  FTC 20 Hz - 20 kHz, 0.1% THD
  EIA 1 kHz, 0.1% THD
1600 W
1800 W2 ohms 
  FTC 20 Hz-20 kHz 0.1% THD
  EIA 1 kHz 1% THD
2000 W
2500 W BRIDGE-MONO MODE8 ohms 
  FTC 20 Hz-20 kHz 0.1% THD
  EIA 1 kHz 0.1% THD
3200 W
3600 W4 ohms 
   EIA 1 kHz 1% THD
5000 WDistortion (SMPTE-IM)Less than 0.02%Distortion (Typical)
20 Hz - 20 kHz: 10 dB below rated power
1 kHz and below: full rated power
Less than 0.02%
Less than 0.02%Frequency Response

20 Hz - 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB
5 Hz - 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dBDamping FactorGreater than 250 @ 8 ohmNoise (unweighted)100 dB below rated output (20 Hz - 20 kHz, 8 ohm load)Input Sensitivity1.42 Vrms for 1050 watts into 8 ohmsVoltage Gain64x (36 dB) for 8 ohm loadInput Impedance20k ohm balanced, 10k ohm unbalancedControls Front:
Controls Rear:

AC power switch, Ch. 1 and Ch. 2 gain control
10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel.Indicators

Power-On: Green LED, Protect: Red LED
Signal -30dB: Yellow LED, Clip: Red LEDConnectors Input:
Connectors Output:XLR female, TRS (1/4"), and barrier-strip screw terminals, each channel
Binding posts and Speakon® outputs (Ch. 1 Speakon wired for biamp)CoolingContinuously variable-speed fan, rear-to-front air flowAmplifier Protection

Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loadsLoad ProtectionOn/off muting, DC fault output crowbarPower Requirements100, 120 or 240 Volts AC (±10%) 50-60 Hz (factory configured)
120V models require 20 Amp service and are supplied with a NEMA 5-20 plug on the cordset. Dimensions19" (48.3 cm) wide, 5.25" (13.3 cm) tall, 15.9" (40.39 cm) overall depthWeight75 lbs (34.02 kg) net, 87 lbs (39.46 kg) shipping

All Specs Subject to Change Without Notice.